E-B
Emulsa Bond is a stir-in latex/acrylic paint additive for exterior wood,
masonry or aluminum siding that helps alleviate peeling problems when
painting over a sound but chalky or dusty surface. E-B Emulsa Bond provides
a bonding oil, stirs in easily, and does not alter the original finish
coat color. It offers a time-saving benefit by eliminating the need to
prime.
BASIC
USES
• For exterior use only
• Apply EB Emulsa Bond modified paint over sound but chalky paint
(latex or oil); sandblasted masonry or weathered, but sound asbestos siding
• Ideal for repainting chalky aluminum siding, T1-11 exterior plywood
or hardboard siding and cementitious siding
GENERAL
REPAINTING WITH E-B EMULSA BOND
SURFACE PREPARATION:
1. Follow directions on latex paint label.
2. Wash protected areas (overhangs, porch ceilings, etc.) with Flood Wood
Cleaner or detergent and water.
3. Rinse thoroughly before painting.
4. If mildew exists remove with a solution of 4 ounces of non-ammoniated
detergent (TSP) 1 quart of outdoor bleach and 3 quarts of fresh water.
Allow this solution to remain on the surface for 10-15 minutes, then rinse
thoroughly.
5. Avoid contact with eyes and skin, and provide adequate ventilation.
6. Rinse thoroughly with fresh water and allow washed areas to dry before
painting.
APPLICATION
NOTE: Use only in the first coat of paint
1. Shake container well.
2. Always mix a small amount of E-B Emulsa Bond with paint to test compatibility.
3. For latex house paint, add 32 oz. (1 qt.) E-B Emulsa Bond per gallon.
4. Stir paint and E-B Emulsa Bond mixture thoroughly. If thickening occurs,
add enough tap water (up to 8 oz/gal) to return to the consistency of
original paint.
5. Paint as usual.
6. Do not recoat with additional E-B Emulsa Bond / paint mixture. If painting
additional coats or a finish coat, apply when the E-B Emulsa Bond / paint
mixture feels dry. Do not apply more paint while the film feels soft or
tacky.
COVERAGE:
While coverage will vary with the texture and porosity of the surface,
you will generally use 20% less material than if the paint or stain had
been applied without E-B Emulsa Bond.
RESTRICTIONS:
Use only in the first coat. Do not add E-B Emulsa Bond to gloss latex
paints for the first coat. E-B Emulsa Bond is not for interior use.
NOTE: Use of latex paint, with or without E-B Emulsa Bond, over heavy
accumulations of old, brittle, checked or cracked paints is not recommended.
E-B
SOLID HIDING STAIN SYSTEM
This system provides water protection and a color coat of latex in one
application. It is designed for repainting previously painted or stained
exterior T1-11 plywood and hardboard. The mixture consists of 50% exterior
latex paint and 50% E-B Emulsa Bond.
MIXING
DIRECTIONS:
NOTE: Custom tinted colors or paints of different manufacturing batch
numbers must be blended or boxed together and thoroughly mixed to assure
uniformity of color PRIOR to mixing with E-B Emulsa Bond.
• Fill 1/3 of a container with well mixed latex house paint and
add an equal amount of E-B Emulsa Bond
• Stir or box this mixture until all of the E-B Emulsa Bond disappears
into the paint
• If thickening occur, add tap water (no more than1/2 pint per gallon)
to bring the mixture back to the consistency of the original paint
APPLICATION:
1. Apply one full hiding coat by brush, roller or sprayer.
2. If the desired appearance is not achieved in one coat, a second coat
of paint WITHOUT E-B Emulsa Bond should be applied.
CLEANUP
& STORAGE
• Clean tools, equipment drips and splatters with a solution of
household detergent and water
• If paint is dry, use paint remover or brush cleaner
• Keep brushes and rollers in water when not in use
• Air dry empty cans and saturated rag, then dispose of according
to local regulations
• Store unused portion in tightly closed container
• KEEP FROM FREEZING |
