Flood CWF-UV 5 OIL Clear Wood Finish is a premium translucent, penetrating oil finish for exterior wood. It is fortified with Flood Penetrol additive for maximum penetration and protection and transparent oxides to guard the wood from ultraviolet damage. It is a clear tint base which blends with in-store colorants to create rich woodtone and semi-transparent shades.

BASIC USES
• For exterior use only
• Weathered exterior woods including Cedar, Redwood, and Pressure Treated Wood.
• Horizontal and vertical surfaces such as decks, siding, shake roofs, fences, docks and furniture
• Allow all new wood to weather 1 year to dry out and open pores before finishing

SURFACE PREPARATION
GENERAL DIRECTIONS:
1. Surfaces must be thoroughly clean, dry and free of dirt, mildew and previous coatings.
2. Remove mildew with a solution of non-amoniated detergent (TSP) 1 quart of outdoor bleach and 3 quarts of fresh water. Allow this solution to remain on the surface for 10-15 minutes, then rinse thoroughly.
3. Clean unfinished weathered wood with Flood Wood Cleaner or Flood Dekswood®.
4. Remove old finishes with Flood Wood Stripper or FloodPro Stripper/Cleaner.
5. After cleaning, allow wood to dry 48 hours or until it has reached a moisture content of 15% or less before finishing.

NEW WOOD SURFACES:
New wood surfaces have a hard shiny surface called mill glaze that prevents maximum penetration and bonding of a finish. To properly prepare the surface for application, treat with a solution of Flood Wood Stripper, diluted one quart per gallon of water. Test wood for absorbency by sprinkling water on the surface. If water is absorbed rapidly, the surface is ready for finishing.

WEATHERED WOOD SURFACES:
Uncoated wood surfaces that have weathered longer than six months require thorough cleaning before applying a finish. Use Flood Wood Cleaner or Flood Dekswood (according to label instructions), along with a pressure washer or stiff bristle brush to remove the loose fiber, dirt and other surface contaminants.

PREVIOUSLY COATED SURFACES:
Apply to bare wood surface or a weathered wood surface that was previously finished with CWF-UV 5 OIL. Other previous stain, varnish or sealers must be completely and thoroughly removed with Flood Wood Stripper or FloodPro Stripper/Cleaner per label directions, before proceeding.
NOTE: Cedar and Redwood may darken with Flood Wood Stripper or FloodPro Stripper/Cleaner. If this occurs brighten with Flood Wood Cleaner or Flood Dekswood before proceeding.

APPLICATION
CAUTION: Surfaces are slippery when wet. Use caution when walking on wet surfaces during application.
1. Stir. Do not thin. Test color in small area.
2. Mix thoroughly before and periodically during application.
3. For color uniformity, intermix in one container, all product to be used on an entire section.
4. Cover everything you do not wish to coat, including plants and shrubs.
5. Apply between 50°F and 80°F.
6. Do not apply if cold and/or wet weather is expected within 24 hours.
7. Always work the entire length of a deck board or horizontal siding to
a logical break, such as a window or door frame.
8. Vertical siding should be coated from top to bottom.
9. Never stop application in the middle of the board or wall.
10.Never apply in direct sun light or on hot surfaces.
11. For external use only, do not use indoors.
12.Apply liberally with a brush or roller, then backbrush.
13.Two coats are recommended. Apply a second coat before the first coat dries (usually within 30 minutes). Do not apply a second coat if the first coat has dried.
14.After spray application, backbrush or backroll to improve penetration and uniformity of coverage.
15.Allow the second coat to penetrate for 10-15 minutes then wipe up any finish that has not penetrated to even out appearance and to avoid shiny spots.

COVERAGE
• 100 - 200 sq. ft/gal (30 - 60 sq. m/gal)
• Coverage varies based on age and density of wood

DECK MAINTENANCE
• Most decks do not have to be coated every year
• A single coat of Flood CWF-UV 5 OIL every second to third year will be sufficient to refresh the natural beauty of your deck and to maintain protection
• Between recoats, a periodic cleaning with Flood Wood Cleaner and Brightener to remove dirt and contamination will renew the appearance of the wood
• Surfaces with harsh exposures to the sun, weather or foot traffic will show wear more quickly than other areas – if this happens, clean effected areas with Flood Wood Cleaner and recoat as necessary, blending into areas which still have good color
• For general recoating follow directions in “Surface Preparation” and “Application”

SIDING MAINTENANCE
• Vertical surfaces do not require annual maintenance
• Surfaces with harsh exposures to the sun and weather will show wear more quickly than other areas – if this happens, clean effected areas with Flood Wood Cleaner and recoat as necessary, blending into areas which still have good color
• Areas retaining good color do not need recoating
• Badly weathered areas may require 2 coats (apply the second coat before the first coat dries)
• Backbrush or backroll to improve penetration and uniformity of coverage

CLEANUP & STORAGE
• Cleanup with mineral spirits
• Store unused portion in tightly closed container