CWF OIL Clear Wood Finish is a penetrating oil finish that provides deep protection against moisture damage. When CWF OIL is first applied, the wood will darken to a richer color, and then begin to lighten depending on the intensity of sun exposure. CWF OIL finish provides a mildew-resistant finish that protects and beautifies exterior wood.

BASIC USES
• For exterior use only
• Weathered exterior woods including Cedar, Redwood and Pressure-Treated Wood
• Horizontal and vertical surfaces such as decks, siding, fences, furniture
• Do not use on roofing shakes or shingles, hardboard, plywood, including T1-11 or over previously stained, varnished or painted wood
• Do not use in screened-in or enclosed areas

SURFACE PREPARATION
GENERAL DIRECTIONS:
1. Surfaces must be thoroughly clean, dry and free of dirt, grease, grime, mildew and previous coatings.
2. Remove mildew with a solution of 4 ounces of non-ammoniated detergent (TSP), 1 quart of outdoor bleach and 3 quarts of fresh water. Allow this solution to remain on the surface for 10-15 minutes, then rinse thoroughly.
3. Clean weathered wood with Flood Wood Cleaner and Brightener, or Flood Dekswood®.
4. Remove old finishes with Flood Wood Stripper or FloodPro® Stripper/Cleaner.
5. After cleaning, allow wood to dry 48 hours or until it has reached a moisture content of 15% or less before finishing.

NEW WOOD SURFACES:
New wood surfaces have a hard shiny surface called mill glaze that prevents maximum penetration and bonding of a finish. To properly prepare the surface for application, treat with a solution of Flood Wood Stripper, diluted one quart per gallon of water. Test wood for absorbency by sprinkling water on the surface. If water is absorbed rapidly, the surface is ready for finishing.

WEATHERED WOOD SURFACES:
Uncoated wood surfaces that have weathered longer than six months require thorough cleaning before applying a finish. Use Flood Wood Cleaner or Flood Dekswood (according to label instructions), along with a pressure washer or stiff bristle brush to remove the loose fiber, dirt and other surface contaminants.

PREVIOUSLY COATED SURFACES:
Apply to bare wood surface or a weathered wood surface that was previously finished with CWF OIL. Other previous stain, varnish or sealers must be completely and thoroughly removed with Flood Wood Stripper or FloodPro Stripper/Cleaner per label directions, before proceeding.

NOTE: Cedar and Redwood may darken with Flood Wood Stripper or FloodPro Stripper/Cleaner. If this occurs brighten with Flood Wood Cleaner or Flood Dekswood before proceeding.

APPLICATION TOOLS
• Brush: High quality, natural bristle stain brush
• Roller: 3/8”-3/4” lambs wool or mohair roller covers
• Spray: Air-Less sprayer .011 - .015 fluid tip/ 700-800 psi or less
• Garden Sprayer

APPLICATION
CAUTION: Surfaces are slippery when wet. Use caution when walking on wet surfaces during application.
1. Stir. Do not thin. Test color in small area.
2. Mix thoroughly before and periodically during application.
3. For color uniformity, intermix in one container, all stain to be used on an entire section.
4. Cover everything you do not wish to coat, including plants and shrubs.
5. Apply between 50°F and 80°F.
6. Do not apply if cold and/or wet weather is expected within 48 hours.
7. Always work the entire length of a deck board or horizontal siding to a logical break, such as a window or door frame.
8. Vertical siding should be coated from top to bottom.
9. Never stop application in the middle of the board or wall.
10. Never apply in direct sun light or hot surfaces.
11. For external use only, do not use indoors.
12. Two coats are recommended. Apply a second coat before the first coat dries (usually within 20 minutes). Do not apply a second coat if the first coat has dried.
13. After spray application, backbrush or backroll to improve penetration and uniformity of coverage.
14. Wipe up any puddles to avoid shiny areas, (within 30 minutes).

NOTE: Remember, CWF OIL is not a surface coating. It protects by penetrating the wood providing a rich matte finish.

COVERAGE
• 100-200 sq. ft/gal (9.3-18.6 sq. m/gal)
• Coverage will vary depending on type, age and texture of wood
• On recoats you will need about half the materials you used the first time

DECK MAINTENANCE
• Most decks do not have to be coated every year
• A single coat of CWFOIL every second year will be sufficient to refresh the natural beauty of your deck and to maintain protection
• Between recoats, a periodic cleaning with Flood Wood Cleaner or Dekswood Cleaner and Brightener to remove dirt and contamination will renew the appearance of the wood.

SIDING MAINTENANCE
• CWF OIL renewal applications are touchup coats
• When coated areas turn gray, apply a coat of CWF OIL to replace material which has weathered away
• Areas retaining good color do not need recoating
• Badly weathered areas may require 2 coats (apply the second coat before the first coat dries)
• Backbrush or backroll to improve penetration and uniformity of coverage
• Surfaces with harsh exposures to the sun and weather will show wear more quickly than other areas. If this happens, clean effected areas with Flood Wood Cleaner or Flood Dekswood and recoat as necessary, blending into areas which still have good color. Areas retaining good color do not need recoating.

CLEANUP & STORAGE
• Mineral Spirits – If CWF OIL is allowed to dry on tools it can be removed with paint remover
• Store unused portion in tightly closed container
• KEEP FROM FREEZING